Non Slip Indoor Floor Coating
(800) 790-9299

SolidStepCote 01 prevents slip and fall accidents in areas that are less likely to become extremely wet or slippery. It offers a relatively smooth texture, and provides slip resistance with the use of very small aggregate particles and nanotechnology materials; similar in texture to 400-grit sandpaper.

SolidStepCote 01 is designed for indoor surfaces that need anti slip protection, but must maintain a close appearance to the original surface. It is a favorable solution for polished stone surfaces such as marble and granite found in homes and lobbies; as well as wood- or vinyl-laminate flooring in homes and office environments. This eco-friendly product contains extremely low VOC's, and has no fumes or odors. It can be applied easily with a paint brush, paint roller or low pressure airless spray.

SolidStepCote may be applied by brush, roller (short nap) or low pressure airless spray. A gallon of SolidStepCote can provide protection over approximately 350 square feet depending on the nature of the surface. Stir or shake the SolidStepCote container vigorously to mix well prior to use. The targeted surface should be free of dirt, debris and oil or grease, prior to application. The coating goes on easily and dries to a clear glossy finish.

One coat is usually sufficient. However if a second is desired, allow the first coat to dry thoroughly for an hour or more depending on ambient temperature. Allow 24 hours or more for full cure before subjecting the surface to heavy traffic. Do not apply at temperatures below 5°F or above 90°F. Avoid heavy buildup, puddling and overlapping. Application Instructions Sheet

Appropriately mask off areas that need to be kept free of SolidStepCote. Wipe off overruns, spills and splatters immediately with water. Thoroughly clean hands and tools after use with soap and warm water. Observe all personal precautions as you would with any other paint or coating product.

SolidStepCote 01 Product Data Sheet
SolidStepCote 01 MSDS
SolidStepCote 01 Technical Data

SolidStepCote 02 is our recommended solution for homes and businesses that must prevent slip and fall accidents while still maintaining floor aesthetics. It features a fine aggregate, similar to 200 grit sandpaper which is almost invisible to the eye, but still addresses floor safety. SolidStepCote 02 creates an easy to clean surface for traditional floor cleaning modalities, including mopping. And it is a perfect fit for any indoor flooring surface such as VCT, concrete, ceramic tile and more.

Common environments for SolidStepCote 02 include, but are not limited to: hospitals, restaurants (dining areas), grocery stores, retail stores, bathroom floors, foyers and hallways. This eco-friendly product contains extremely low VOC's, and has no fumes or odors. It can be applied easily with a paint brush, paint roller or low pressure airless spray.

SolidStepCote may be applied by brush, roller (short nap) or low pressure airless spray. A gallon of SolidStepCote can provide protection over approximately 350 square feet depending on the nature of the surface. Stir or shake the SolidStepCote container vigorously to mix well prior to use. The targeted surface should be free of dirt, debris and oil or grease, prior to application.

The coating goes on easily and dries to a clear glossy finish. One coat is usually sufficient. However if a second is desired, allow the first coat to dry thoroughly for an hour or more depending on ambient temperature. Allow 24 hours or more for full cure before subjecting the surface to heavy traffic. Do not apply at temperatures below 5°F or above 90°F. Avoid heavy buildup, puddling and overlapping. Application Instructions Sheet

SolidStepCote, due to its textured nature, will attract and hold dirt and oils and must be cleaned regularly to dislodge or break down the buildup of contaminants that will, over time, create discoloration in the surface. SolidStepCote may be cleaned daily with mops or nylon bristle brushes and standard liquid floor cleaners. Clean your SolidStepCote treated floor, tub or other surface periodically as needed with a soft to medium nylon bristled brush or push broom using a non-solvent based cleaner/degreaser.

*WARNING! DO NOT clean SolidStepCote treated surfaces with highly abrasive tools such as Scouring Pads, Motorized Rotary Cleaning Devices, Abrasive Sponges, Burnishing Devices, Steel Brushes, Diamond Pads, Sandpapers or other Buffing Devices. Over abrasion will damage the surface of the coating, removing the non-slip textured aggregate and damaging the surface appearance. DO NOT use Harsh Chemical Solvents to clean as they may damage or remove the coating.

Appropriately mask off areas that need to be kept free of SolidStepCote. Wipe off overruns, spills and splatters immediately with water. Thoroughly clean hands and tools after use with soap and warm water. Observe all personal precautions as you would with any other paint or coating product.

SolidStepCote 02 Product Data Sheet
SolidStepCote 02 MSDS
SolidStepCote 02 Technical Data
02 Test Report

SolidStepCote 03 is our most popular formula to prevent slip and fall accidents indoors and outdoors. The surface is coarser than SolidStepCote 02, with texture similar to 100-grit sandpaper. It provides greater slip resistance for homes and businesses that are more likely to encounter wet or slippery surfaces. It is designed for intense indoor protection and lighter outdoor protection.

SolidStepCote 03 may be applied on any surface where flooring aesthetics aren't a concern. Due to the solution's enhanced slip resistance, the original surface aesthetic becomes less visible compared to SolidStepCote 02. This eco-friendly product contains extremely low VOC's, and has no fumes or odors. It can be applied easily with a paint brush, paint roller or low pressure airless spray. It's the preferred solution for bathtubs and showers.

SolidStepCote may be applied by brush, roller (short nap) or low pressure airless spray. A gallon of SolidStepCote can provide protection over approximately 350 square feet depending on the nature of the surface. Stir or shake the SolidStepCote container vigorously to mix well prior to use. The targeted surface should be free of dirt, debris and oil or grease, prior to application.

The coating goes on easily and dries to a clear glossy finish. One coat is usually sufficient. However if a second is desired, allow the first coat to dry thoroughly for an hour or more depending on ambient temperature. Allow 24 hours or more for full cure before subjecting the surface to heavy traffic. Do not apply at temperatures below 5°F or above 90°F. Avoid heavy buildup, puddling and overlapping. Application Instructions Sheet

Appropriately mask off areas that need to be kept free of SolidStepCote. Wipe off overruns, spills and splatters immediately with water. Thoroughly clean hands and tools after use with soap and warm water. Observe all personal precautions as you would with any other paint or coating product.

SolidStepCote 03 Product Data Sheet
SolidStepCote 03 MSDS
SolidStepCote 03 Wet Pendulum Test Results

SolidStepCote 04 is our most effective non slip solution for more industrial indoor and outdoor environments. It's our coarsest solution, similar to 50-grit sandpaper for environments that are more likely to encounter slip and fall accidents due to wet or slippery surfaces; caused by rain, pool water, oil or grease. In industrial settings, a two-coat application will not chip, even with intense friction. And may be cleaned using a bristled brush.

Common indoor uses include: factories, warehouses, commercial kitchens, auto repair shops, pool decks, spas and more. And outdoor uses include, but are not limited to: stairs, pool decks, wood decks, composite decking, entryways and more. This eco-friendly product contains extremely low VOC's, and has no fumes or odors. It can be applied easily with a paint brush, paint roller or low pressure airless spray.

SolidStepCote may be applied by brush, roller (short nap) or low pressure airless spray. A gallon of SolidStepCote can provide protection over approximately 350 square feet depending on the nature of the surface. Stir or shake the SolidStepCote container vigorously to mix well prior to use. The targeted surface should be free of dirt, debris and oil or grease, prior to application. The coating goes on easily and dries to a clear glossy finish. One coat is usually sufficient. However if a second is desired, allow the first coat to dry thoroughly for an hour or more depending on ambient temperature. Allow 24 hours or more for full cure before subjecting the surface to heavy traffic. Do not apply at temperatures below 5°F or above 90°F. Avoid heavy buildup, puddling and overlapping. Application Instructions Sheet

Appropriately mask off areas that need to be kept free of SolidStepCote. Wipe off overruns, spills and splatters immediately with water. Thoroughly clean hands and tools after use with soap and warm water. Observe all personal precautions as you would with any other paint or coating product.

SolidStepCote 04 Product Data Sheet
SolidStepCote 04 MSDS
SolidStepCote 04 COF Test Data

SolidStepCote 02 DIY Tub and Shower Kit is our gentlest solution to prevent slip and fall accidents in bathtubs and showers. This do-it-yourself kit features our SolidStepCote 02 formula, similar in texture to 200-grit sandpaper. It?s less abrasive on bare skin and appropriate for those who enjoy bathing as well as showering. SolidStepCote 02 DIY Kit applies easily creating a clear, virtually invisible finish that works on all tubs and showers including porcelain, acrylic, fiberglass, cast iron, ceramic and decorative tile.

Other features include:

The surface should be completely dry and free of dirt, debris and oil or grease prior to application. Thoroughly clean the surface to be coated with water and a standard cleaner to remove dirt, dust and stains. Dry surface before applying product.

1) Clean tub or shower surface thoroughly, making sure to remove any dirt or other contaminants.
2) Lightly shake contents of bottle.
3) Pour 1-2 oz. of product into provided paint tray. Swirl occasionally to mix aggregate.
4) Roll on to tub or shower surface gently and evenly with the provided roller (product is self-leveling).
*If applying two coats for greater durability and lifespan, allow 1st coat to dry to touch (15-20 minutes) before applying 2nd coat.
5) Allow 3 hours drying time (at 75F and 50% relative humidity) before showering, 24 hours before bathing. Do not apply at temperatures below 50° F or above 90° F.

Clean your SolidStepCote treated floor, tub or other surface as needed with a mop, sponge or nylon bristled brush using water and any liquid household tub or shower cleaner.

DO NOT clean SolidStepCote treated surfaces with highly abrasive tools such as Scouring Pads or Abrasive Sponges. Abrasion will damage the surface of the coating, removing the non-slip textured aggregate and damaging the surface appearance. DO NOT use Chemical Solvents to clean as they may dissolve the coating.

One 4 oz. kit will treat 1 standard sized tub, one 8 oz. kit treats 2 standard tubs or 1 large walk-in shower with a 2-coat application. For most tubs and showers 2 oz. will provide a single coating over 6 square feet. With proper care and a 2-coat application, the SolidStepCote treated tub should last for 3-5 years before needing reapplication.

SolidStepCote 03 DIY Tub and Shower Kit is the perfect solution to prevent slip and fall accidents in bathtubs and showers that require more slip resistance. This do-it-yourself kit features our SolidStepCote 03 formula, similar in texture to 100-grit sandpaper. It's less abrasive on bare skin and appropriate for those who primarily shower rather than bathing.

SolidStepCote 03 DIY Kit applies easily creating a clear, virtually invisible finish that works on all tubs and showers including porcelain, acrylic, fiberglass, cast iron, ceramic and decorative tile.

Other features include:

The surface should be completely dry and free of dirt, debris and oil or grease prior to application. Thoroughly clean the surface to be coated with water and a standard cleaner to remove dirt, dust and stains. Dry surface before applying product.

1) Clean tub or shower surface thoroughly, making sure to remove any dirt or other contaminants.
2) Lightly shake contents of bottle.
3) Pour 1-2 oz. of product into provided paint tray. Swirl occasionally to mix aggregate.
4) Roll on to tub or shower surface gently and evenly with the provided roller (product is self-leveling).
*If applying two coats for greater durability and lifespan, allow 1st coat to dry to touch (15-20 minutes) before applying 2nd coat.
5) Allow 3 hours drying time (at 75F and 50% relative humidity) before showering, 24 hours before bathing. Do not apply at temperatures below 50° F or above 90° F.

Clean your SolidStepCote treated floor, tub or other surface as needed with a mop, sponge or nylon bristled brush using water and any liquid household tub or shower cleaner.

DO NOT clean SolidStepCote treated surfaces with highly abrasive tools such as Scouring Pads or Abrasive Sponges. Abrasion will damage the surface of the coating, removing the non-slip textured aggregate and damaging the surface appearance. DO NOT use Chemical Solvents to clean as they may dissolve the coating.

One 4 oz. kit will treat 1 standard sized tub, one 8 oz. kit treats 2 standard tubs or 1 large walk-in shower with a 2-coat application. For most tubs and showers 2 oz. will provide a single coating over 6 square feet. With proper care and a 2-coat application, the SolidStepCote treated tub should last for 3-5 years before needing reapplication.